hippi: Move the HIPPI driver

Move the HIPPI driver into drivers/net/hippi/ and make the
necessary Kconfig and Makefile changes.

CC: Jes Sorensen <jes@wildopensource.com>
CC: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

MAINTAINERS

@@ -3049,6 +3049,7 @@ S:	Maintained
 F:	include/linux/hippidevice.h
 F:	include/linux/if_hippi.h
 F:	net/802/hippi.c
+F:	drivers/net/hippi/
 
 HOST AP DRIVER
 M:	Jouni Malinen <j@w1.fi>

drivers/net/Kconfig

@@ -272,38 +272,6 @@ config RIONET_RX_SIZE
 	depends on RIONET
 	default "128"
 
-config HIPPI
-	bool "HIPPI driver support (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && INET && PCI
-	help
-	  HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
-	  1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
-	  can run over copper (25m) or fiber (300m on multi-mode or 10km on
-	  single-mode). HIPPI networks are commonly used for clusters and to
-	  connect to super computers. If you are connected to a HIPPI network
-	  and have a HIPPI network card in your computer that you want to use
-	  under Linux, say Y here (you must also remember to enable the driver
-	  for your HIPPI card below). Most people will say N here.
-
-config ROADRUNNER
-	tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
-	depends on HIPPI && PCI
-	help
-	  Say Y here if this is your PCI HIPPI network card.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called rrunner.  If unsure, say N.
-
-config ROADRUNNER_LARGE_RINGS
-	bool "Use large TX/RX rings (EXPERIMENTAL)"
-	depends on ROADRUNNER
-	help
-	  If you say Y here, the RoadRunner driver will preallocate up to 2 MB
-	  of additional memory to allow for fastest operation, both for
-	  transmitting and receiving. This memory cannot be used by any other
-	  kernel code or by user space programs. Say Y here only if you have
-	  the memory.
-
 config PLIP
 	tristate "PLIP (parallel port) support"
 	depends on PARPORT

drivers/net/Makefile

@@ -13,7 +13,6 @@ obj-$(CONFIG_VMXNET3) += vmxnet3/
 # link order important here
 #
 obj-$(CONFIG_PLIP) += plip.o
-obj-$(CONFIG_ROADRUNNER) += rrunner.o
 obj-$(CONFIG_RIONET) += rionet.o
 
 #
@@ -39,6 +38,7 @@ obj-$(CONFIG_VETH) += veth.o
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_ETHERNET) += ethernet/
 obj-$(CONFIG_FDDI) += fddi/
+obj-$(CONFIG_HIPPI) += hippi/
 onj-$(CONFIG_PPP) += ppp/
 obj-$(CONFIG_PPP_ASYNC) += ppp/
 obj-$(CONFIG_PPP_BSDCOMP) += ppp/

drivers/net/hippi/Kconfig

+#
+# HIPPI network device configuration
+#
+
+config HIPPI
+	bool "HIPPI driver support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && INET && PCI
+	---help---
+	  HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
+	  1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
+	  can run over copper (25m) or fiber (300m on multi-mode or 10km on
+	  single-mode). HIPPI networks are commonly used for clusters and to
+	  connect to super computers. If you are connected to a HIPPI network
+	  and have a HIPPI network card in your computer that you want to use
+	  under Linux, say Y here (you must also remember to enable the driver
+	  for your HIPPI card below). Most people will say N here.
+
+if HIPPI
+
+config ROADRUNNER
+	tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
+	depends on PCI
+	---help---
+	  Say Y here if this is your PCI HIPPI network card.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called rrunner.  If unsure, say N.
+
+config ROADRUNNER_LARGE_RINGS
+	bool "Use large TX/RX rings (EXPERIMENTAL)"
+	depends on ROADRUNNER
+	---help---
+	  If you say Y here, the RoadRunner driver will preallocate up to 2 MB
+	  of additional memory to allow for fastest operation, both for
+	  transmitting and receiving. This memory cannot be used by any other
+	  kernel code or by user space programs. Say Y here only if you have
+	  the memory.
+
+endif /* HIPPI */

drivers/net/hippi/Makefile

+#
+# Makefile for the HIPPI network device drivers.
+#
+
+obj-$(CONFIG_ROADRUNNER) += rrunner.o