This patch adds export/import support to sha256-s390.  The exported
type is defined by struct sha256_state, which is basically the entire
descriptor state of sha256_generic.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds export/import support to sha1-s390.  The exported
type is defined by struct sha1_state, which is basically the entire
descriptor state of sha1_generic.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When the aes-intel module is loaded on a system that does not have the
AES instructions, it prints

    Intel AES-NI instructions are not detected.

at level KERN_ERR.  Since aes-intel is aliased to "aes" it will be tried
whenever anything uses AES and spam the console.  This doesn't match
existing practice for how to handle "no hardware" when initializing a
module, so downgrade the message to KERN_INFO.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Just started running fips cavs test vectors through an s390x system
for giggles, and discovered that I missed patching s390's arch-specific
des3 implementation w/an earlier des3 patch to permit weak keys.

This change adds the same flag tweaks as
ad79cdd7 (crypto: des3_ede - permit
weak keys unless REQ_WEAK_KEY set) for s390's des3 implementation,
yields expected test results now.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

kernel_fpu_begin/end used preempt_disable/enable, so sleep should be
prevented between kernel_fpu_begin/end.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Because AES-NI instructions will touch XMM state, corresponding code
must be enclosed within kernel_fpu_begin/end, which used
preempt_disable/enable. So sleep should be prevented between
kernel_fpu_begin/end.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Original implementation of aesni_cbc_dec do not save IV if input
length % 4 == 0. This will make decryption of next block failed.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

ia64 was assigning resources to root busses after allocations had
been made for child busses.  Calling pcibios_setup_root_windows() from
pcibios_fixup_bus() solves this problem by assigning the resources to
the root bus before child busses are scanned.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This function was only used by pci_claim_resource(), and the last commit
deleted that use.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It is generally agreed that it would be beneficial for u64 to be an
unsigned long long on all architectures.  ia64 (in common with several
other 64-bit architectures) currently uses unsigned long.  Migrating
piecemeal is too painful; this giant patch fixes all compilation warnings
and errors that come as a result of switching to use int-ll64.h.

Note that userspace will still see __u64 defined as unsigned long.  This
is important as it affects C++ name mangling.

[Updated by Tony Luck to change efi.h:efi_freemem_callback_t to use
 u64 for start/end rather than unsigned long]

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Andrew cleaned up some #include tangles in:
commit 0d9c25dd
  headers: move module_bug_finalize()/module_bug_cleanup() definitions into module.h

which resulted in this build error for ia64:
  CC      arch/ia64/kernel/paravirt_patchlist.o
arch/ia64/kernel/paravirt_patchlist.c:43: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__initdata'
arch/ia64/kernel/paravirt_patchlist.c:54: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'paravirt_get_gate_patchlist'
arch/ia64/kernel/paravirt_patchlist.c:76: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'paravirt_get_gate_section'
make[1]: *** [arch/ia64/kernel/paravirt_patchlist.o] Error 1

The problem was that paravirt_patchlist.c was relying on some of the
nested includes (specifically that linux/bug.h included linux/module.h

Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

[Ralf: SMP support requires CPU hotplugging which MIPS currently doesn't
support.  As implemented in this patch cache and tlb flushing will also be
invoked with interrupts disabled so smp_call_function() will blow up in
charming ways.  So limit to !SMP.]

Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Yan Hua <yanh@lemote.com>
Reviewed-by: Arnaud Patard <apatard@mandriva.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We had an ugly #ifdef for Cavium Octeon hwrena bits in traps.c, remove
it to mach-cavium-octeon/cpu-feature-overrides.h

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some CPUs have implementation dependent rdhwr registers.  Allow them
to be enabled on a per CPU basis.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add new kconfig variables SYS_SUPPORTS_HUGETLBFS and
CPU_SUPPORTS_HUGEPAGES.  They are enabled for systems that are known
to support huge pages.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The TLB handlers need to check for huge pages and give them special
handling.  Huge pages consist of two contiguous sub-pages of physical
memory.

* Loading entrylo0 and entrylo1 need to be handled specially.

* The page mask must be set for huge pages and then restored after
  writing the TLB entries.

* The PTE for huge pages resides in the PMD, we halt traversal of the
  tables there.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The octeon-ethernet driver needs to check for additional chip specific
features, we add them to the octeon_has_feature() framework.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The bootloader now uses additional board type constants.  The
octeon-ethernet driver needs some of the new values.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The various Octeon ethernet drivers use these new functions.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Replace a few open-coded GPIO register accesses with gpio calls.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Replace a few GPIO register accesses in the board init code with calls to
the gpio api.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Replace a few GPIO register accesses in the board init code with calls
to the gpio api.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases.  To address this, the following changes are made:

* create generic functions which deal with manipulating the on-chip
  GPIO1/2 blocks.  Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.

  If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
  compatibility by directly inlining the GPIO1/2 functions.  GPIO access
  is limited to on-chip ones and they can be accessed as documented in
  the datasheets (GPIO0-31 and 200-215).

  If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
  one for GPIO2, are registered.  GPIOs can still be accessed by using
  the numberspace established in the databooks.

  However this is not yet flexible enough for my uses:  My Alchemy
  systems have a documented "external" gpio interface (fixed, different
  numberspace) and can support a variety of baseboards, some of which
  are equipped with I2C gpio expanders.  I want to be able to provide
  the default 16 GPIOs of the CPU board numbered as 0..15 and also
  support gpio expanders, if present, starting as gpio16.

  To achieve this, a new Kconfig symbol for Alchemy is introduced,
  CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
  that they don't want the Alchemy numberspace exposed to the outside
  world, but instead want to provide their own.  Boards are now respon-
  sible for providing the linux gpio interface glue code (either in a
  custom gpio.h header (in board include directory) or with gpio_chips).

  To make the board-specific inlined gpio functions work, the MIPS
  Makefile must be changed so that the mach-au1x00/gpio.h header is
  included _after_ the board headers, by moving the inclusion of
  the mach-au1x00/ to the end of the header list.

  See arch/mips/include/asm/mach-au1x00/gpio.h for more info.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

gpio_direction_output should also set an output value according to the API.

Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 o Rewrite to use <asm-generic/ioctl.h>.  Cuts down the file from 40 to
   16 lines.
 o Delete _IOC_VOID, _IOC_OUT, _IOC_IN and _IOC_INOUT.  They were added
   for 2.1.14 but I was not able to find any user - not even historical
   ones.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add platform support for RNG of TX4939 SoC.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add a sysdev to access SRAM in TXx9 SoCs via sysfs.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch removes the SiByte simulation Kconfig option, which only modified
a printk.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove commented out definitions.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch.  This
label in the switch statement is dead code, so we remove it.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>